Shoe marks can turn a perfectly clean commercial floor into an untidy one within a short time, and they are frequently found in the entrances of shopping centres, in reception areas, down the corridors, in the lift lobbies, in schools, in gyms and in the foyers of offices, particularly in places where dark rubber soles rub across smooth floors.
The floor finish has many scuff marks on the surface rather than the marks going into the material. Professional cleaners start by using the mildest method and only increase the strength of the cleaning when it is necessary to protect the surface while efficiently removing the scuff marks. Here’s how to do it like professional day time cleaners in Melbourne.
Prepare the Area Before You Start
Start by checking what type of floor you have because vinyl, laminate, sealed timber, polished tile and other hard surfaces react differently to water, friction or cleaning chemicals.
Wherever possible, first sweep, dust mop or vacuum the area in question. Sand, grit and dirt tracked in can cause scratches on a finished surface when the surface is rubbed with a cloth, an eraser or a tennis ball.
Start with a Damp Microfiber Cloth
Start off by using the simplest method. Take a clean microfiber cloth and wet it slightly with a little water or with a floor cleaner that is suitable for the surface. The cloth should be damp, not wet.
Use short and controlled strokes to rub the scuff away. Fresh rubber transfer is often removed by light friction. When the mark has disappeared, clean off any residue and dry the area. If the scuff remains visible, go on to the following method instead of scrubbing the surface again.
Try a Clean Tennis Ball for Rubber Marks
A tennis ball can be used to remove black marks from many types of sealed hard floors since its felt surface provides sufficient friction to lift the rubber transfer without the need for a strong chemical.
It is advisable to use a clean ball since a dirty tennis ball may carry grit which can scratch the floor. Rub the ball over the mark with moderate pressure. In the case of larger commercial areas, cleaners usually put a tennis ball on the end of a broom or mop handle so that they can carry out quick spot cleaning while standing.
First, test a concealed section on timber, laminate or specialty flooring and then adhere to the floor manufacturer’s maintenance instructions.
Use a White Eraser for Small Stubborn Spots
A white pencil eraser that is clean is effective when dealing with small spots where the scuff is concentrated in one area; it should be rubbed gently over the transfer and the rubbing should stop as soon as the mark begins to lift, while coloured or dirty erasers should be avoided since they might leave residue behind.
Next, remove the eraser dust and, if the floor manufacturer permits it, finish by using a clean damp cloth, then dry the surface.
Be Careful with Stronger Cleaning Methods
Do not immediately take to using abrasive powder, a strong solvent or a scouring pad if there is a mark. These products might remove the scuff but could at the same time damage the finish of the floor.
When it comes to resilient flooring, it is necessary to use a neutral cleaner which has been approved by the manufacturer or to apply a spot treatment. With sealed timber, one should avoid using too much water or solvents that are not approved. For polished stone, vinyl or coated floors, vigorous rubbing may affect the shine and result in a dull area.
Baking soda and solvent-based cleaners are at times recommended for tough scuffs, but they should only be used where the floor manufacturer has confirmed that they are compatible. A safer method when using commercial products is to first test the mildest one that is approved in a spot which is not noticeable.
Wipe, Dry and Inspect the Floor
Once the mark has disappeared, take out any dust or residue left by the cleaner or eraser. Follow the floor-care instructions by using a clean cloth and then wipe the area dry with a microfibre cloth. Make sure that moisture is not left on timber, laminate joints or any other moisture-sensitive surfaces.
Look for any smears, dull areas, or any leftover residue; if the surface appears different, then stop and instead check the floor-care instructions rather than trying to polish it more.
Prevent Scuffs from Building Up
It is most effective to carry out cleaning during the day if the scuffs are removed when they are still small. While carrying out their regular patrols, the cleaners should examine the entrances, the areas near the escalators, the food courts, the reception areas and other busy zones. Using entrance mats also helps to reduce the grit which causes scratching.
When dealing with problems that occur repeatedly, you should investigate the cause; for example, rubber furniture feet, trolley wheels, movable displays and footwear might be leaving marks in the same spot repeatedly.
Final Thoughts
You don’t need to scrub harshly to remove shoe scuff marks from hard floors. First, sweep away any loose dust, and then use a damp microfibre cloth, a clean tennis ball or a white eraser. If the mark is still there, proceed to use an approved cleaning product and consider the finish of the floor before increasing either the friction or the strength of the chemical.
Keen to Clean offers commercial properties help with cleaning on a scheduled day, as well as with floor maintenance and the care of high-traffic areas. If you’d like a quote, please get in touch.



































































